15% Off Orders Over $125
Promo Code: JEDI.

This is a demo store. Any orders placed through this store will not be honored or fulfilled.

Text Us 952-260-4404

Center of Gravity® Brew Sculpture

More Views

Center of Gravity® Brew Sculpture

SKU: 41465

We've taken our premium brewstand and upgraded the burners to give you more heating power. Now featuring a larger burner element that boasts 65,000 BTUs per tier! Speed up your brewing process! A revolutionary, pro-quality brew sculpture in a powerful, compact package—at a compact price.

The Center of Gravity® is built to brew right out of the box. Everything you need from burners to propane lines. Virtually tool-free setup. A tiny total footprint of just one square meter. Quick, compact storage. Center of Gravity® is the first all-in-one brew sculpture that you can set up in 15 minutes and break down to fit in a hockey bag.

Free Shipping on Orders Over $45



An innovative design delivers a structure both powerful and portable. Sturdy yet surprisingly lightweight, the Center of Gravity® brew stand weighs only 90 lbs. It is easy to move and even travel with—break it down and throw it in the trunk of your car for the ultimate brewcation! The Center of Gravity® is perfect for brewers who lack the storage space for a more permanent brew stand.

Kettles up to 19 inches tall can be used with this gravity brew stand. Check out our 15 gallon MegaPot 1.2™ for the perfect size kettle for 5 or 10 gallon batches.

The very top tier is where your Hot Liquor tank will be placed. Pre-heat your sparge water during the mash and have hot water on demand when you want it.

Your Mash Tun will be placed on the middle tier. No more bending or reaching to monitor strike temperature, add grains, check mash pH, and watch the flow-rate of the sparge. Direct fire your mash kettle to maintain accurate mash temperatures or step-mash schedules using the precise needle valve control on the propane burner.

The bottom burner tier will hold your boil kettle 26 inches off the floor. When the mash is complete, easily collect your pre-boil wort, pump-free. Once you've boiled and chilled, conveniently drain directly into your sanitized fermentor. There’s enough height to feed a counter-flow chiller with gravity too.

Each burner can be controlled independently. Heat the sparge water while you mash, or start preparing strike water for a second batch, while finishing the boil on the first.

Pair this with the MegaPot 1.2™ Pro All-Grain Brewing System for the all grain brewing stand of your dreams..

It’s the last brew sculpture you’ll ever need for making beer at home—or in the wild.

Made in the USA from domestic and imported components.

Watch our video here

Proposition 65 Warning for California Consumers: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.
Details & Instructions

Additional Information

2.3 / 5.0
4 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Brew Sculpture
Probably be ok. It will take time to plumb it and will be a while before I have time to use it
January 1, 2016
Save your money
Save your money you would need it to burn in order to get a full wort kettle to boil. Even on a 90 degree day this thing could not keep 7.5 gallons of wort boiling. It is definitely not going to work at 45 or 50 degrees. It will help maintain a good sparge temperature but that is the extent of it's ability.
July 1, 2015
Looks good on paper or on the web
Looks good on paper or on the web but fails to perform in the field. Today with an outside temperature in the lower 80s and starting with water at about 85 degrees I could not get 5.5 gallons to boil. It was all it could do to get the water to 150 degrees steeping temperature. And that is with just one of the burners going. I tried two different propane tanks just in case it was a gas problem. It was not. Fortunately I have another burner I was able to use to finish my brew day. If not for that it would have been a really bad day.
August 17, 2015
Don't use close to flammable materials
Even though I tested before I started my brew I still had two separate hose fires during the steeping process and had to finish with another furnace. Be very careful using this device. If possible replace or repair every connection on the hoses.
May 4, 2016
Response from Midwest Supplies - V4.3 - test
Hope there was no damage. Always a good idea to test for any leaks and read all instructions to ensure it is used safely. This has not been the normal experience. Do you need our help with any damaged or defective items? Cheers!
October 7, 2016
Midwest Supplies
Response from Midwest Supplies - V4.3 - test
Hope there was no damage. Always a good idea to test for any leaks and read all instructions to ensure it is used safely. This has not been the normal experience. Do you need our help with any damaged or defective items? Cheers!
October 27, 2016
Midwest Supplies
Customer Q&A
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 4 answers
What is the pressure rating of the regulator and can it handle two burners going simultaneously?
Robert J on Aug 15, 2016
BEST ANSWER: It can handle all three burners full on. I have 10 gal pots and it heats fast. I love being able to setup and take down by me self.
Has anyone else had problems with propane leaks. I est this system every-time I use it. But a few minutes into the steeping process it develops leaks. Today I went to the restroom, washed my hands and returned to find a fire at the hose connections. I repaired that then awhile later another connection caught fire. Then to make matters worse two of the three swivel connectors started to leak. Event though I tested before I started and after each repair I had new leaks. This could have been a catastrophic failure. The entire hose assembly should be rebuilt or replaced.
Seeker on May 4, 2016
BEST ANSWER: So, did you find leaks after testing? Not sure if it the connections are too loose or defective in some way? I guess the only way would be to test for leaks during use at all times and make note of when a leak develops. The instructions should go over where and what should be tightened and how much - then a spray bottle will let you find any leaks...not sure why it would develop on its own without manipulation. We'd be happy to send a replacement for all hoses and assemblies if you think that will help...Cheers.

Call Us 888-449-2739

Text Us 952-260-4404

Please wait...

Your selected product has been added to your Cart.

Continue Shopping Go To Cart